Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Gate Repair in Bloomington, CA
Gate access control in Bloomington usually means one of two jobs: a keypad or intercom retrofit on an older ranch gate, or a full card-reader system on a commercial yard entrance off Slover or Santa Ana Avenue. Most calls we run in Bloomington involve gate hardware that has to survive 110-degree summers, Santa Ana wind, and daily use by horse trailers or delivery trucks. It’s a different workload than a cleaner, purely residential neighborhood. Call us at (909) 764-3720 and we’ll give you a written price before any work starts.
Why Bloomington Homes Are Different
Bloomington is unincorporated San Bernardino County, and the gate mix reflects that. The same street can have a 1960s ranch on a half-acre horse lot with a tubular steel gate that weighs 400 pounds, and a trucking yard with a cantilever slide gate that runs fifty cycles a day. That dual residential-agricultural-commercial mix means gate repair in Bloomington rarely fits a standard playbook. Older post-and-rail gates sag because the original posts were never set in concrete, and many automatic gates were installed without county permits. Summer heat above 110°F warps wood frames and pushes gate opener motors past their thermal limits. Fall Santa Ana winds knock marginally hung gates off their tracks. The climate and the lot sizes mean the hardware takes more abuse here than it does two miles away in Fontana or Rialto, where lots are smaller and gates are lighter. Bloomington also runs every gate permit through San Bernardino County, not a city building department, and that surprises a lot of homeowners.
Our Main Bloomington Services
These are the three services Bloomington homeowners and property managers call us about most often.
Gate Repair in Bloomington
A sagging gate, a bottom wheel that binds on the track, or a hinge that drops the gate an inch every month are common here. We repair the existing gate rather than pushing a replacement: new hinge pins, reinforced post plates, straightened rails, re-welded pickets. The focus is making the gate plumb and balanced again. On automatic gates, we pull the motor, check the limit switches, and photograph everything after the repair. Winter rain and summer heat both affect how the posts settle in Bloomington’s silty soil. Gate Repair in Bloomington covers the full detail.

Gate Installation in Bloomington
New gates in Bloomington usually go onto existing posts, or we set new posts in concrete at the same time. The county permit requirement applies to any automatic gate installation, which some contractors skip. We handle the permit paperwork with San Bernardino County and bring the gate up to current code, including proper safety edges and photo-eyes. On horse properties, we build gates wide enough for a two-horse trailer and heavy enough to survive daily use by equipment. Gate Installation in Bloomington has the full breakdown.

Gate Motor & Opener in Bloomington
A worn-out motor or a circuit board that shuts down on a 108-degree afternoon is a common call. We service nine major automation brands so we can usually keep the existing opener alive rather than replacing it. The job includes photo-eye alignment, limit switch calibration, and a load test with the gate moving. Wiring at older Bloomington properties is often undersized for modern draw, which we check before blaming the motor. Gate Motor & Opener in Bloomington has specifics.

Before
AfterGate Access Control in Bloomington

Gate Access Control in Bloomington means retrofitting control electronics onto older gates that were built before keypad entry was common. Many 1950s-era ranch properties here have simple swing gates with a chain and padlock, and the owner wants a keypad, a card reader, or an intercom added without replacing the gate itself. In a place with this many horse properties and trucking yards, access control is often a practical fix: let boarders open the gate with a code, let the driver into the yard with a card, and keep the gate locked otherwise.
Keypad Entry
Signs you need it
You’re giving out gate codes to every visitor and can’t tell who came or went.
What it costs in Bloomington
Keypad entry installation in Bloomington typically runs $850-$1,600 per gate, complete with the control board and programming.
How we do it
We mount the keypad at vehicle height, run the conductor back to the operator’s control board, and program unique or shared codes before photographing the wiring.
Video Intercom
Signs you need it
You have to walk or drive to the gate to see who is there, or the gate opens blind every time the bell rings.
What it costs in Bloomington
Video intercom systems in Bloomington range from $2,200 to $4,300 on average, depending on whether the wire already exists or we have to pull new cable.
How we do it
We place the camera at the gate approach, connect it to a monitor inside the house or on your phone, and program the gate-release button on the same unit.
What Gate Access Control Costs in Bloomington
| Item | Typical range in Bloomington |
|---|---|
| Keypad entry retrofit | $850-$1,600 |
| Video intercom with remote release | $2,200-$4,300 |
| Full access control system on a commercial gate | $2,400-$4,800 |
Can you add a keypad to an older Bloomington gate without replacing it?
Yes, in most cases we can mount a keypad and wire it into the existing gate operator’s control board. The gate frame and posts need to be structurally sound first; if the post is rotted, we address that before hanging new electronics.
Do Bloomington gate access systems need a permit?
Automatic gate systems in unincorporated San Bernardino County do require county permit approval when they include a new operator or significant electrical work. The permit process sits with the county, not a city building department. We handle the paperwork on every access control job.
Gate Parts & Welding in Bloomington

Gate Parts & Welding in Bloomington is the hands-on work of putting a worn gate back into square. Decades-old tubular steel gates on ranch lots often suffer cracked welds at the hinge joints, bent top rails, and bottom rollers that have worn flat. We weld the break, replace the worn part, and leave a photographed record of the work.
Hinge Replacement
Signs you need it
The gate drags on one corner or drops when you open it, and the hinge pin is worn to a shine.
What it costs in Bloomington
Hinge replacement in Bloomington typically runs $180 to $480 per set, including re-hanging and greasing the new pins.
How we do it
We lift the gate with a floor jack, cut the old hinge barrels, weld or bolt the new set to the post, and set the gate back plumb.
Gate Rollers
Signs you need them
A sliding gate grinds along the track or the roller wheels wobble because the bearings are gone.
What it costs in Bloomington
Gate roller replacement in Bloomington runs $140 to $320 per pair, welded and aligned to the existing track.
How we do it
We unbolt the old rollers, match the bearing size, weld the new brackets to the gate frame, and test the slide with the gate fully loaded.
What Gate Parts & Welding Costs in Bloomington
| Item | Typical range in Bloomington |
|---|---|
| Hinge replacement (per set) | $180-$480 |
| Gate roller replacement (per pair) | $140-$320 |
| Custom welding on a damaged gate | $220-$580 |
Can you weld a gate that broke at the hinge in Bloomington?
Yes, we weld cracked hinge joints and broken pickets as long as the surrounding steel is not paper-thin from rust. The gate goes back plumb, not just patched. Every weld gets a photo in the job record.
Do you replace just the rollers or only the whole gate?
Just the rollers, in most cases. We replace the pair, match the wheel diameter to your track, and align the gate so it rolls without dragging. We only suggest a full gate replacement when the frame itself is structurally gone.
Brands We Service in Bloomington
We service LiftMaster, FAAC, BFT, and Linear openers on both residential and commercial gates in Bloomington. Common boards and remotes for LiftMaster and Linear are stocked locally, so a control board replacement often happens the same day. For less common FAAC and BFT parts we order with next-day delivery. See our brands for the full service list.
Pricing for Gate Repair in Bloomington, CA

| Service | Typical range in Bloomington |
|---|---|
| Gate access control: keypad entry | $850-$1,600 |
| Gate access control: video intercom | $2,200-$4,300 |
| Gate access control: full commercial system | $2,400-$4,800 |
| Hinge replacement (per set) | $180-$480 |
| Gate roller replacement (per pair) | $140-$320 |
| Custom welding repair | $220-$580 |
| Post replacement with concrete set | $420-$1,100 |
| Rail repair and straightening | $180-$420 |
| Gate opener motor replacement (swing) | $1,200-$2,800 |
| Gate opener motor replacement (slide) | $1,800-$3,400 |
| Photo-eye replacement and alignment | $150-$350 |
| Full gate installation (automatic, single swing) | $4,200-$9,500 |
What pushes a Bloomington quote up is usually the gate’s weight and span. A heavy ranch gate with a long leaf needs a larger post, a heavier hinge, or a stronger operator, and all of that moves the number. Every price is written down and handed to you before any tool comes off the truck.
Neighborhoods We Serve in Bloomington
We cover the whole community. Response time is usually same-day for urgent gate failures, next-day at the latest; the geography is tight enough that we’re rarely more than 20 minutes out. Representative neighborhoods:
- Marygold
- Crestmore
- Slover
- Linden
- South Bloomington
Service Area - Cities Near Bloomington

We serve Bloomington and the surrounding area. If you’re in Rialto, CA, Fontana, CA, Mira Loma, CA, or Rancho Cucamonga, CA, the same crew and the same written-price rule apply. Call (909) 764-3720 to schedule.
Serving Bloomington, CA - Our Local Coverage Area
We’re serving the Bloomington area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Bloomington

For urgent gate failures we typically arrive the same day, and a live person answers the phone at any hour to schedule it. Bloomington’s compact geography means we’re rarely more than 20 minutes from most properties. The exact arrival window is confirmed when you call.
Repairs to the existing gate and its hardware typically do not require a permit. Adding a new automatic opener or running new electrical line usually does, and it’s a San Bernardino County process rather than a city one. We confirm the permit requirement before any work starts.
Yes. The written price comes to you before any work begins, and you approve it first. No work is done on an open-ended estimate, and no surprise invoice arrives at the end. That’s the only way we work in Bloomington.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within the hour.
- 4You approve before work beginsNothing starts until you say go.
What Bloomington Customers Say
"The safety loop had never been installed correctly by the previous company. They showed me the reading, fixed it, and did not charge me for the diagnosis."
- Patrick H."Honest about what did not need doing. Told me the operator had years left and only the control board needed replacing."
- Douglas N."Our gate was hit by a delivery truck. They came out, documented the damage properly for the insurer, and the claim went through without an argument."
- Camille R.





Before
After
Before
After